How to Install a Bathtub
How to Install a Bathtub
Blog Article
Everybody maintains their private piece of advice about A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't precisely brain surgery, but it does need solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a new one is likewise a moderately challenging task. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also position the new tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old tub and set in the new one. Ensure you have certified on your own for the task as well as fit trying it. As opposed to hiring a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your bathroom if you have already purchased a new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and material list should comprise the following:
Preparing for the Setup
First of all, the supporting structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing taps can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. When the supply pipes have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before proceeding to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub until the level checks out level.
To install faucets, fit all-time low of the outermost flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leakages and tighten them if necessary. Load the tub and additionally inspect the overflow outlet and the regular outlet for leaks.
Lastly, fix the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub ought to wait till the bathtub has actually been made use of a minimum of once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Secure the tap in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former type needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with moisture and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes and cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bathtub with water before securing, to permit the activity experienced when the tub remains in usage. The sealer can split rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads about How to Install a Bathtub Yourself, I assumed sharing that piece of content was essential. Do you know anybody else who is excited by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Do not hesitate to promote it. Many thanks for your time. Please stop by our blog back soon.
Book An Appointment Report this page